Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
Parts & Accessories

$24.99
Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable.
- Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers)
- Plug has O-ring retention – no tool required

$40.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 141mm - 1 axle per bag

$13.73
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 15mm - 1 cone per bag Note: O-ring / seal not included. Check the seal groove closely. This cone has a narrower groove than cone CN-R002. COMPATIBLE HUBS: - 105 FH-5700, 9 speed (right side cone) - 105 SC 1051, 7 Speed Rear - RX100 A551, 8 Speed Rear - RSX 410, 7 Speed Rear - Deore LX M550, 7 Speed Rear - Deore Mtn LX M550, 7 Speed Rear

$14.52
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Cone Diameter: 14.8mm - Dust Seal Diameter: 22mm - Length: 10.6mm - 1 cone per bag COMPATIBLE HUBS: - Tiagra 4400 Front - Shimano Sora HB-3300 Front - Shimano Acera HB-M330 Front - Shimano Nexave HB-T300 Front

$1.80 - $7.35
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels.
- 14mm x 1mm (1411-AN) sold in pairs
- All others sold individually

$6.79
- Variable widths
- Left: 35mm
- Center: 52mm
- Right: 40.5mm
- Length: 127.5mm
- Overall: 148.5mm

$18.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant.
Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads:
- MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi
- ERD 615, 622x49.9, 29 in x 52.3mm
Your rim has a stepped valve and is not compatible with this Schrader valve.

$16.00
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair.
Identifying your Hugo rim and selecting the correct valve stem:
Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim.
Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads:
MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi
ERD 615, 622x49.9, 29 in x 52.3mm
Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.

$5.49
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!

$16.99
- Replacement rear wheel skewer.
- Specifically designed for use with Saris trainers.
- Can be used for both indoor and outdoor rides.

$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season.
- When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out.
- The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability.
- No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

$2.99
The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

$7.99
Replacement freehub spoke protector, in various sizes for different freehub sizes.
- Made of clear plastic
- 3 hooks for affixing to spokes

$49.99
The buyer's choice for wheel builders looking to save weight.
ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond.
- 32 nipples weigh approximately 30 grams

$15.79 - $64.00
The buyer's choice for wheel builders looking to save weight.
The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use.
- Weight: starting at 20g for 64 nipples

$16.00
Rack Fit System Long Quick Release.
Compatible with:
- Outpost Front Rack
- Outpost Rear Rack
- Central Rear Rack
- Interlock Rear Rack

$24.00
Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

$70.00
- Wheel bearing kit front/rear
- Bearing dimensions: 17 x 30 x 7mm
- Material: steel
- 2 pieces

$19.00 - $31.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

$7.00
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm.
Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

$390.00
- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings
Page 1 of 15
Next page